Резервирование
Блок управления отчетами может использоваться одновременно только одним клиентом. Оба партнера по резервированию «КАСКАД Цифра» используют один и тот же RCB, однако значения от устройства получает только активный клиент. В случае резервного переключения клиент, который будет пассивным, должен освободить RCB, прежде чем другой клиент сможет его использовать.
В зависимости от используемого типа RCB поведение при резервном переключении различно:
- URCB — выпускается немедленно
- BRCB — недоступен для другого клиента до истечения срока, определенного в ReserveTms Срок действия элемента точки данных истек. Поэтому значение ReserveTms должно быть задано как можно меньшим (1 секунда).
Фактическое время переключения зависит от причины потери соединения. Например, оба партнера должны обнаружить потерю соединения. Если клиент «КАСКАД Цифра» обнаруживает обрыв соединения сразу, то то, как быстро ИЭУ обнаруживает обрыв соединения и отпускает RCB, зависит от типа устройства.
Поэтому рекомендуется использовать BRCB для передачи важных данных. При потере соединения данные записываются в буфер BRCB и передаются в хронологическом порядке после восстановления соединения. В зависимости от конфигурации Чтение завершенного буфера извлекается весь буфер или только отчеты, накопленные за время простоя.
Флаги отладки
DEBUG_DRV_CONF
Предоставляет информацию о конфигурации, например, при создании, включении, удалении или отключении конфигураций адресов.
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:32:03.508, DEBUG_DRV_CONF, «Added DataPoint 7SJ62.IED_7SJ62CTRL/Q0CSWI1$CO$Pos$Oper$ctlVal mode 1»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:32:03.508, DEBUG_DRV_CONF, «Added DataPoint 7SJ62.IED_7SJ62CTRL/Q0CSWI1$CO$Pos$Oper$operVal mode 1»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:32:03.509, DEBUG_DRV_CONF, «Added DataPoint 7SJ62.IED_7SJ62CTRL/Q0CSWI1$CO$Pos$Oper$error mode 2»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:32:03.510, DEBUG_DRV_CONF, «Added DataPoint 7SJ62.IED_7SJ62CTRL/Q0CSWI1$CO$Pos$Oper$addCause mode 2»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:32:03.510, DEBUG_DRV_CONF, «Added DataPoint 7SJ62.IED_7SJ62CTRL/Q1CSWI1$CO$Pos$Oper$ctlVal mode 1»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:32:03.665, DEBUG_DRV_CONF, «New server 7SJ82 added»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:32:03.665, DEBUG_DRV_CONF, «New server anvil added»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:32:03.665, DEBUG_DRV_CONF, «New server 7SJ62 added»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:32:03.671, DEBUG_DRV_CONF, «New RCB: D01_7SJ82CTRL/LLN0$BR$A_BRCB_1801 added for server 7SJ82»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:32:03.672, DEBUG_DRV_CONF, «New RCB: D01_7SJ82CTRL/LLN0$RP$A_URCB_1101 added for server 7SJ82»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:32:03.673, DEBUG_DRV_CONF, «New RCB: D01_7SJ82CTRL/LLN0$RP$A_URCB_1801 added for server 7SJ82»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:32:03.679, DEBUG_DRV_CONF, «New RCB: IED1LogicalDevice1/LLN0$RP$urcb1 added for server anvil»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:32:03.679, DEBUG_DRV_CONF, «New RCB: IED_7SJ62CTRL/Q0CSWI1$RP$urcbA01 added for server 7SJ62»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:32:03.698, DEBUG_DRV_CONF, «Logical device list request sent to server anvil to get ResvTms and Report ID data types.»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:32:03.705, DEBUG_DRV_CONF, «MMS tag list response received for Logical device class 9 from server anvil»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:32:03.706, DEBUG_DRV_CONF, «MMS tag list request for Logical device IED1LogicalDevice1 send to server anvil»
DEBUG_DRV_SENT
Shows the target address on the device for the sent telegrams.
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:38:56.426, DEBUG_DRV_SENT, «Identify request send to server anvil»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:38:56.429, DEBUG_DRV_SENT, «Logical device list request sent to server anvil»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:38:56.433, DEBUG_DRV_SENT, «Identify request send to server 7SJ62»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:38:56.434, DEBUG_DRV_SENT, «Logical device list request sent to server 7SJ62»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:38:56.435, DEBUG_DRV_SENT, «Identify request send to server 7SJ82»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:38:56.435, DEBUG_DRV_SENT, «Logical device list request sent to server 7SJ82»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:38:56.452, DEBUG_DRV_SENT, «Dataset list request for Logical device IED_7SJ62CTRL send to server 7SJ62»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:38:56.452, DEBUG_DRV_SENT, «Dataset list request for Logical device D01_7SJ82CTRL send to server 7SJ82»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:38:56.483, DEBUG_DRV_SENT, «Dataset list request for Logical device D01_7SJ82DR send to server 7SJ82»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:38:56.514, DEBUG_DRV_SENT, «Dataset list request for Logical device IED_7SJ62DR send to server 7SJ62»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:38:56.516, DEBUG_DRV_SENT, «Dataset list request for Logical device D01_7SJ82MEAS send to server 7SJ82»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:38:56.529, DEBUG_DRV_SENT, «Dataset list request for Logical device IED_7SJ62DR send to server 7SJ62»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:38:56.552, DEBUG_DRV_SENT, «Dataset list request for Logical device D01_7SJ82PROT send to server 7SJ82»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:38:56.564, DEBUG_DRV_SENT, «Dataset list request for Logical device IED_7SJ62EXT send to server 7SJ62»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:38:56.584, DEBUG_DRV_SENT, «Dataset list request for Logical device IED_7SJ62MEAS send to server 7SJ62»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:38:56.595, DEBUG_DRV_SENT, «Dataset attribute request send for D01_7SJ82CTRL/CBT_GAPC1$dyn_pers to server 7SJ82»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:38:56.605, DEBUG_DRV_SENT, «Dataset list request for Logical device IED_7SJ62PROT send to server 7SJ62»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:38:56.616, DEBUG_DRV_SENT, «Dataset attribute request send for D01_7SJ82CTRL/CBT_GAPC1$im117816 to server 7SJ82»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:38:56.637, DEBUG_DRV_SENT, «Dataset attribute request send for IED_7SJ62CTRL/CALH1$pm259f to server 7SJ62»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:38:56.637, DEBUG_DRV_SENT, «Dataset attribute request send for D01_7SJ82CTRL/LLN0$Breaker to server 7SJ82»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:38:56.658, DEBUG_DRV_SENT, «Dataset attribute request send for D01_7SJ82DR/LLN0$mjeidler to server 7SJ82»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:38:56.949, DEBUG_DRV_SENT, «Dataset attribute request send for IED_7SJ62CTRL/LLN0$measures to server 7SJ62»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:38:56.961, DEBUG_DRV_SENT, «Dataset attribute request send for IED_7SJ62CTRL/Q0CSWI1$im117375 to server 7SJ62»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:39:02.531, DEBUG_DRV_SENT, «Write Boolean value for IED_7SJ62CTRL/Q0CSWI1$RP$urcbA01$Resv»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:39:13.022, DEBUG_DRV_SENT, «Write request for 7SJ62.IED_7SJ62CTRL/Q1CSWI1$CO$Pos$Oper$ctlVal»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:39:13.035, DEBUG_DRV_SENT, «Write Control Struct IED_7SJ62CTRL/Q1CSWI1$CO$Pos$Oper»
DEBUG_DRV_RCVD
Issues either the source address of received telegrams on the device or the type of the received message.
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:25:51.998, DEBUG_DRV_RCVD, «writeDataToDp: anvil.IED1LogicalDevice1/GGIO1$MX$AnIn1$mag$f»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:25:52.000, DEBUG_DRV_RCVD, «writeDataToDp: 7SJ62.IED_7SJ62CTRL/Q0CSWI1$ST$Pos$stSeld»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:25:52.002, DEBUG_DRV_RCVD, «writeDataToDp: 7SJ62.IED_7SJ62CTRL/Q0XCBR1$ST$Pos$stVal»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:25:52.999, DEBUG_DRV_RCVD, «writeDataToDp: anvil.IED1LogicalDevice1/GGIO1$MX$AnIn1$mag$f»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:25:51.354, DEBUG_DRV_RCVD, «MMS tag list response received for Logical device D01_7SJ82PROT class 0 from server 7SJ82»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:25:51.373, DEBUG_DRV_RCVD, «MMS tag list response received for Logical device D01_7SJ82CTRL class 0 from server 7SJ82»
DEBUG_DRV_COMMAND
Provides information on service requests that are using the control model.
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:45:16.733, DEBUG_DRV_COMMAND, «Writing Controllable Object IED_7SJ62CTRL/Q0CSWI1$CO$Pos$SBOw to the Server: 7SJ62 with following values:
WCCOAiec618502:Control value: 1
WCCOAiec618502:Ctlnum value: 59
WCCOAiec618502:Test: 0
WCCOAiec618502:Check: no-check
WCCOAiec618502:Originator: MD1A5S6C_IEC_61850_dev_RCBState_2
WCCOAiec618502:Category: 2″
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:45:16.756, DEBUG_DRV_COMMAND, «Write Response for Controllable Object IED_7SJ62CTRL/Q0CSWI1$CO$Pos$SBOw from Server: 7SJ62 is Success»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:45:22.909, DEBUG_DRV_COMMAND, «Writing Controllable Object IED_7SJ62CTRL/Q0CSWI1$CO$Pos$Oper to the Server: 7SJ62 with following values:
WCCOAiec618502:Control value: 1
WCCOAiec618502:Ctlnum value: 59
WCCOAiec618502:Test: 0
WCCOAiec618502:Check: no-check
WCCOAiec618502:Originator: MD1A5S6C_IEC_61850_dev_RCBState_2
WCCOAiec618502:Category: 2″
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:45:22.937, DEBUG_DRV_COMMAND, «Write Response for Controllable Object IED_7SJ62CTRL/Q0CSWI1$CO$Pos$Oper from Server: 7SJ62 is Success»
DEBUG_DRV_REPORT
Shows which values are sent from an RCB to «КАСКАД Цифра». Outputs are only available for configured addresses.
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:50:47.528, DEBUG_DRV_REPORT, «writeDataToDp: anvil.IED1LogicalDevice1/GGIO1$MX$AnIn1$mag$f»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:50:48.529, DEBUG_DRV_REPORT, «writeDataToDp: anvil.IED1LogicalDevice1/GGIO1$MX$AnIn1$mag$i»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:50:49.530, DEBUG_DRV_REPORT, «writeDataToDp: anvil.IED1LogicalDevice1/GGIO1$ST$Mod$stVal»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:55:29.250, DEBUG_DRV_REPORT, «writeDataToDp: 7SJ62.IED_7SJ62CTRL/Q0CSWI1$ST$Pos$stSeld»WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:50:51.530
DRV_REPORT_CONFIG
Provides information on enabling/disabling RCBs
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:59:43.363, DRV_REPORT_CONFIG, «Process RCB response: device: 7SJ62| report: _7SJ62_IED_7SJ62CTRL_Q0CSWI1_RP_urcbA01| index: | request: Reserve RCB| attribute: Resv| value: 1| is manual: 1»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:59:43.376, DRV_REPORT_CONFIG, «Process RCB response: device: 7SJ62| report: _7SJ62_IED_7SJ62CTRL_Q0CSWI1_RP_urcbA01| index: | request: Read RCB Attributes| attribute: urcbA01| value: 1| is manual: 1»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:59:43.379, DRV_REPORT_CONFIG, «Attribute read OK: urcbA01»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:59:43.390, DRV_REPORT_CONFIG, «Process RCB response: device: 7SJ62| report: _7SJ62_IED_7SJ62CTRL_Q0CSWI1_RP_urcbA01| index: | request: Write dynamic dataset| attribute: stSeldTest| value: IED_7SJ62CTRL/CALH1$stSeldTest| is manual: 1»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:59:43.411, DRV_REPORT_CONFIG, «Process RCB response: device: 7SJ62| report: _7SJ62_IED_7SJ62CTRL_Q0CSWI1_RP_urcbA01| index: | request: Write RCB Attribute| attribute: DatSet| value: IED_7SJ62CTRL/CALH1$stSeldTest| is manual: 1»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:59:43.412, DRV_REPORT_CONFIG, «OK: DatSet»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:59:43.412, DRV_REPORT_CONFIG, «Process RCB response: device: 7SJ62| report: _7SJ62_IED_7SJ62CTRL_Q0CSWI1_RP_urcbA01| index: | request: Write RCB Attribute| attribute: RptID| value: 1| is manual: 1»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:59:43.414, DRV_REPORT_CONFIG, «OK: RptID»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:59:43.414, DRV_REPORT_CONFIG, «Process RCB response: device: 7SJ62| report: _7SJ62_IED_7SJ62CTRL_Q0CSWI1_RP_urcbA01| index: | request: Write RCB Attribute| attribute: OptFlds| value: 1| is manual: 1»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:59:43.415, DRV_REPORT_CONFIG, «OK: OptFlds»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:59:43.416, DRV_REPORT_CONFIG, «Process RCB response: device: 7SJ62| report: _7SJ62_IED_7SJ62CTRL_Q0CSWI1_RP_urcbA01| index: | request: Write RCB Attribute| attribute: TrgOps| value: 1| is manual: 1»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:59:43.417, DRV_REPORT_CONFIG, «OK: TrgOps»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:59:43.417, DRV_REPORT_CONFIG, «Process RCB response: device: 7SJ62| report: _7SJ62_IED_7SJ62CTRL_Q0CSWI1_RP_urcbA01| index: | request: Write RCB Attribute| attribute: BufTm| value: 100| is manual: 1»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:59:43.418, DRV_REPORT_CONFIG, «OK: BufTm»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:59:43.418, DRV_REPORT_CONFIG, «Process RCB response: device: 7SJ62| report: _7SJ62_IED_7SJ62CTRL_Q0CSWI1_RP_urcbA01| index: | request: Write RCB Attribute| attribute: IntgPd| value: 1000| is manual: 1»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 15:59:43.420, DRV_REPORT_CONFIG, «OK: IntgPd»
DRV_REPORT_RCV
Provides information on received reports. All elements that the report contains are issued regardless if an address is configured or not.
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:04:25.656, DRV_REPORT_RCV, «—————- New report <_anvil_IED1LogicalDevice1_LLN0_RP_urcb1> received»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:04:25.659, DRV_REPORT_RCV, «Type: Unbuffered»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:04:25.659, DRV_REPORT_RCV, «Sequence Num: <1>»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:04:25.660, DRV_REPORT_RCV, «Reason: <GEN_INTER>»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:04:25.660, DRV_REPORT_RCV, «Element at index 0: <IED1LogicalDevice1/GGIO1$ST$Mod>
WCCOAiec618502:»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:04:25.662, DRV_REPORT_RCV, » Attribute at index 0: <GGIO1$ST$Mod$stVal>»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:04:25.663, DRV_REPORT_RCV, » Attribute at index 1: <GGIO1$ST$Mod$q>»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:04:25.665, DRV_REPORT_RCV, » Attribute at index 2: <GGIO1$ST$Mod$t>»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:04:25.666, DRV_REPORT_RCV, «Element at index 1: <IED1LogicalDevice1/GGIO1$CF$Mod>
WCCOAiec618502:»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:04:25.668, DRV_REPORT_RCV, » Attribute at index 0: <GGIO1$CF$Mod$ctlModel>»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:04:25.669, DRV_REPORT_RCV, «Element at index 2: <IED1LogicalDevice1/GGIO1$MX$AnIn1>
WCCOAiec618502:»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:04:25.671, DRV_REPORT_RCV, » Attribute at index 0: <GGIO1$MX$AnIn1$mag$i>»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:04:25.672, DRV_REPORT_RCV, » Attribute at index 1: <GGIO1$MX$AnIn1$mag$f>»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:04:25.674, DRV_REPORT_RCV, » Attribute at index 2: <GGIO1$MX$AnIn1$q>»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:04:25.675, DRV_REPORT_RCV, » Attribute at index 3: <GGIO1$MX$AnIn1$t>»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:04:25.676, DRV_REPORT_RCV, «Element at index 3: <IED1LogicalDevice1/GGIO1$CF$AnIn1>
WCCOAiec618502:»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:04:25.678, DRV_REPORT_RCV, » Attribute at index 0: <GGIO1$CF$AnIn1$db>»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:04:25.679, DRV_REPORT_RCV, » Attribute at index 1: <GGIO1$CF$AnIn1$sVC$scaleFactor>»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:04:25.681, DRV_REPORT_RCV, » Attribute at index 2: <GGIO1$CF$AnIn1$sVC$offset>»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:04:25.683, DRV_REPORT_RCV, «Element at index 4: <IED1LogicalDevice1/GGIO1$CO$SPCSO1>
WCCOAiec618502:»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:04:25.684, DRV_REPORT_RCV, » Attribute at index 0: <GGIO1$CO$SPCSO1$Oper$ctlVal>»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:04:25.686, DRV_REPORT_RCV, » Attribute at index 1: <GGIO1$CO$SPCSO1$Oper$origin$orCat>»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:04:25.688, DRV_REPORT_RCV, » Attribute at index 2: <GGIO1$CO$SPCSO1$Oper$origin$orIdent>»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:04:25.689, DRV_REPORT_RCV, » Attribute at index 3: <GGIO1$CO$SPCSO1$Oper$ctlNum>»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:04:25.691, DRV_REPORT_RCV, » Attribute at index 4: <GGIO1$CO$SPCSO1$Oper$T>»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:04:25.692, DRV_REPORT_RCV, » Attribute at index 5: <GGIO1$CO$SPCSO1$Oper$Test>»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:04:25.694, DRV_REPORT_RCV, » Attribute at index 6: <GGIO1$CO$SPCSO1$Oper$Check>»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:04:25.694, DRV_REPORT_RCV, «Element at index 5: <IED1LogicalDevice1/GGIO1$ST$DPCSO1>
WCCOAiec618502:»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:04:25.695, DRV_REPORT_RCV, » Attribute at index 0: <GGIO1$ST$DPCSO1$stVal>»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:04:25.696, DRV_REPORT_RCV, » Attribute at index 1: <GGIO1$ST$DPCSO1$q>»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:04:25.696, DRV_REPORT_RCV, » Attribute at index 2: <GGIO1$ST$DPCSO1$t>»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:04:25.697, DRV_REPORT_RCV, «—————- Report <_anvil_IED1LogicalDevice1_LLN0_RP_urcb1> done
DRV_REPORT_PROCESS
Provides information on processing of reports. All elements that are contained in the report are issued regardless if an address is configured or not.
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:06:32.003, DRV_REPORT_PROCESS, «—————- Start processsing report <_anvil_IED1LogicalDevice1_LLN0_RP_urcb1>»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:06:32.004, DRV_REPORT_PROCESS, «Element <IED1LogicalDevice1/GGIO1$ST$Mod>»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:06:32.005, DRV_REPORT_PROCESS, » Attribute <GGIO1$ST$Mod$stVal>»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:06:32.005, DRV_REPORT_PROCESS, «Element <IED1LogicalDevice1/GGIO1$CF$Mod>»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:06:32.006, DRV_REPORT_PROCESS, » Attribute <GGIO1$CF$Mod$ctlModel>»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:06:32.007, DRV_REPORT_PROCESS, «Element <IED1LogicalDevice1/GGIO1$MX$AnIn1>»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:06:32.008, DRV_REPORT_PROCESS, » Attribute <GGIO1$MX$AnIn1$mag$f>»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:06:32.008, DRV_REPORT_PROCESS, » Set GI bit»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:06:32.010, DRV_REPORT_PROCESS, » Attribute <GGIO1$MX$AnIn1$mag$i>»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:06:32.010, DRV_REPORT_PROCESS, «Element <IED1LogicalDevice1/GGIO1$CF$AnIn1>»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:06:32.011, DRV_REPORT_PROCESS, » Attribute <GGIO1$CF$AnIn1$sVC$offset>»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:06:32.012, DRV_REPORT_PROCESS, » Attribute <GGIO1$CF$AnIn1$sVC$scaleFactor>»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:06:32.013, DRV_REPORT_PROCESS, » Attribute <GGIO1$CF$AnIn1$db>»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:06:32.013, DRV_REPORT_PROCESS, «Element <IED1LogicalDevice1/GGIO1$CO$SPCSO1>»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:06:32.014, DRV_REPORT_PROCESS, » Attribute <GGIO1$CO$SPCSO1$Oper$Check>»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:06:32.015, DRV_REPORT_PROCESS, » Attribute <GGIO1$CO$SPCSO1$Oper$Test>»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:06:32.016, DRV_REPORT_PROCESS, » Attribute <GGIO1$CO$SPCSO1$Oper$T>»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:06:32.017, DRV_REPORT_PROCESS, » Attribute <GGIO1$CO$SPCSO1$Oper$ctlNum>»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:06:32.018, DRV_REPORT_PROCESS, » Attribute <GGIO1$CO$SPCSO1$Oper$origin$orIdent>»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:06:32.019, DRV_REPORT_PROCESS, » Attribute <GGIO1$CO$SPCSO1$Oper$origin$orCat>»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:06:32.019, DRV_REPORT_PROCESS, » Attribute <GGIO1$CO$SPCSO1$Oper$ctlVal>»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:06:32.020, DRV_REPORT_PROCESS, «Element <IED1LogicalDevice1/GGIO1$ST$DPCSO1>»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:06:32.021, DRV_REPORT_PROCESS, » Attribute <GGIO1$ST$DPCSO1$stVal>»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:06:32.022, DRV_REPORT_PROCESS, «—————- report <_anvil_IED1LogicalDevice1_LLN0_RP_urcb1> done
DRV_DATASET_CONFIG
Provides information on static and dynamic datasets.
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:09:38.076, DRV_DATASET_CONFIG, «anvil: add new dataset <IED1LogicalDevice1/LLN0$set01»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:09:38.076, DRV_DATASET_CONFIG, «anvil: add new dataset <IED1LogicalDevice1/LLN0$set02»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:09:38.077, DRV_DATASET_CONFIG, «anvil: add new dataset <IED1LogicalDevice1/MMXU1$measures»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:09:45.795, DRV_DATASET_CONFIG, «7SJ62, Request: Write dynamic dataset <IED_7SJ62CTRL/CALH1$stSeldTest> triggered by RCB <_7SJ62_IED_7SJ62CTRL_Q0CSWI1_RP_urcbA01>»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:09:45.809, DRV_DATASET_CONFIG, «7SJ62, Request: configure dataset <IED_7SJ62CTRL/CALH1$stSeldTest> for RCB <_7SJ62_IED_7SJ62CTRL_Q0CSWI1_RP_urcbA01>»
WCCOAiec618502:WCCOAiec61850(2), 2015.05.27 16:10:47.800, DRV_DATASET_CONFIG, «7SJ62, Request: Release dynamic dataset <IED_7SJ62CTRL/CALH1$stSeldTest> triggerd by RCB <_7SJ62_IED_7SJ62CTRL_Q0CSWI1_RP_urcbA01>»